View AAT1155_285702.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1MHz 2.5A Buck DC/DC Converter General Description
The AAT1155 SwitchRegTM is a member of AnalogicTechTM's Total Power ManagementTM IC product family. The Step-down switching converter is ideal for applications where high efficiency, small size, and low ripple are critical. Able to deliver 2.5A with an internal power MOSFET, the current-mode controlled IC provides high efficiency. Fully internally compensated, the AAT1155 simplifies system design and lowers external part count. The AAT1155 is available in an MSOP-8 package, rated over -40 to 85C.
AAT1155
Features
* * * * * * * * * * * * * * *
SwitchRegTM
5.5V max supply input -40 to 85C Temperature Range Fixed output voltage: 1.0V - 4.2V 2.5A output current Integrated low on resistance power switches Internally compensated current mode control 1MHz switching frequency Fixed or adjustable VOUT: 1.0 to 4.2V Constant PWM mode Low output ripple with light load Internal softstart Current limit protection Over-Temperature protection MSOP-8 package Up to 95% efficiency
Applications
* * * * * Computer Peripherals Set Top Boxes Network Cards Cable/DSL Modems High efficiency conversion from 5V or 3.3V supply
Typical Application
INPUT
10F
VP FB
AAT1155
ENABLE 100 VCC
LX LX
1.5H
OUTPUT SGND 0.1F PGND 120F
1155.2004.08.1.2
1
1MHz 2.5A Buck DC/DC Converter Pin Descriptions
Pin #
1 2 3 4 5, 8 6, 7
AAT1155
Symbol
FB GND EN VCC VP LX
Function
Feedback input pin Signal ground Converter enable pin Small Signal Filtered Bias Supply Input supply for converter power stage Inductor connection pin
Pin Configuration
MSOP-8
FB GND EN VCC
1
8
VP LX LX VP
1
2 2
7
3
6
4
5
2
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter Absolute Maximum Ratings
Symbol
VCC, VP VLX VFB VEN TJ TLEAD VESD
AAT1155
(TA=25C unless otherwise noted) Value
6 -0.3 to VP+0.3 -0.3 to VCC+0.3 -0.3 to VCC+0.3 -40 to 150 300 3000
Description
VCC, VP to GND LX to GND FB to GND EN to GND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) ESD Rating 1 - HBM
Units
V V V V C C V
Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5K resistor into each pin.
Thermal Characteristics
Symbol
JA PD
Description
Maximum Thermal Resistance (MSOP-8) Maximum Power Dissipation (MSOP-8) 2
2
Value
150 833
Units
C/W mW
Note 2: Mounted on a demo board (FR4, in still air).
Recommended Operating Conditions
Symbol
T
Description
Ambient Temperature Range
Rating
-40 to +85
Units
C
1155.2004.08.1.2
3
1MHz 2.5A Buck DC/DC Converter Electrical Characteristics
values are at TA = 25C) Symbol
VIN VOUT VIL VIH VUVLO VUVLO(HYS) IQ ISHDN ILIM RDS(ON)L VOUT (VOUT*VIN) VOUT/VOUT FOSC TSD THYS
AAT1155
(VIN = VCC = VP = 5V, TA= -40 to 85C unless otherwise noted. Typical
Description
Input Voltage Range Output Voltage Tolerance Input Low Voltage Input Low Voltage Under Voltage Lockout Under Voltage Lockout Hysteresis Quiescent Supply Current Shutdown Current Current Limit High Side Switch On Resistance Efficiency Load Regulation Line Regulation Oscillator Frequency Over Temp Shutdown Threshold Over Temp Shutdown Hysteresis
Conditions
VIN = VOUT + 0.2 to 5.5V, IOUT = 0.5A
Min Typ Max Units
2.7 -2.5 5.5 2.5 0.6 1.4 V % V V V V mV A A A m % %/V MHz C C
VIN Rising VIN Falling No Load, VFB= 0 V VEN = 0 V, VIN= 5.5V TA = 25C TA = 25C IOUT = 1.0 A ILOAD = 0 - 2.5A VIN= 2.7 to 5.5V TA = 25C
2.5 1.2 250 630 4.4 60 92 2.3 0.75 1 140 15 1000 1.0
4
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter Typical Characteristics
RDS(ON) vs. Temperature
90
AAT1155
Oscillator Frequency Variation vs. Supply Voltage (VOUT =3.3V)
0.5
2.7V
80
3.6V
4.2V Variation (%)
120
RDS(ON) (m)
0.25
70 60
0
5.0V
50 40 -20 0 20 40 60 80
5.5V
-0.25
100
-0.5 3.5
4
4.5
5
5.5
Temperature (C)
Input Voltage (V)
RDS(ON) vs. VIN, IDS = 1A
80
Oscillator Frequency Variation vs. Temperature VIN=5V
1
75
RDS(ON) (m)
70 65 60 55 50 45 40 2.5 3 3.5 4 4.5 5 5.5
0
Variation (%)
-1
-2 -3 -4 -20 0 20 40 60 80 100
Input Voltage (V)
Temperature (C)
Enable Threshold vs. Input Voltage
1.2
Output Voltage vs. Temperature IOUT = 2A, VO = 3.3V
0.4
Enable Threshold (V)
1.1 1 0.9 0.8 0.7 0.6 2.5 3 3.5 4 4.5 5 5.5
Variation (%)
EN(H)
0.2 0 -0.2 -0.4 -0.6 -0.8 -20 0 20 40 60 80 100
EN(L)
Input Voltage (V)
Temperature (C)
1155.2004.08.1.2
5
1MHz 2.5A Buck DC/DC Converter Typical Characteristics
Line Regulation VOUT = 3.3V
Output Voltage Error (%)
1 3.6
AAT1155
AAT1155 Evaluation Board Over Temp Current vs. Input Voltage, VOUT = 3.3V
Output Current (A)
3.4 3.2 3 2.8 2.6 2.4 2.2 2 1.8 1.6
0
IO = 0.3A
-1 -2 -3 -4 -5 3.4
55C 70C 85C 100C
3.5 3.75 4 4.25 4.5 4.75 5 5.25 5.5
IO = 3.0A
3.7 4 4.3 4.6 4.9 5.2 5.5
Input Voltage (V)
Input Voltage (V)
Load Regulation VIN = 5.0V, VOUT = 3.3V
-1.0%
Non-Switching Operating Current vs. Temperature, FB = 0V
Operating Current (mA)
750 700 650 600 550 500 450
0.0% -2.0% -3.0% -4.0% -5.0% -6.0% -7.0% -8.0% -9.0% -10.0% 0.01 0.10 1.00 10.00
Output Error (%)
2.7V
3.6V
4.2V
5.0V
5.5V
-20
0
20
40
60
80
100
120
Load Current (A)
Temperature (C)
Enalbe and Output Voltage (V) (top trace)
Over Temp Shutdown Current vs. Temperature VOUT = 3.3V, VIN = 5.0V
5
Inrush and Output Overshoot Characteristic
8 6 4 2 0 -2 -4 -6 -8 0 0.4 0.8 1.2 1.6 2 14
Inductor Current (A) (bottom trace)
12 10 8 6 4 2 0 -2
Output Current (A)
4.5 4 3.5 3 2.5 2 -20 -10 0 10 20 30 40 50 60 70 80 90 100
Temperature (C)
Time (millisec)
6
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter Typical Characteristics
Tantalum Output Ripple IOUT = 3.0A, VOUT = 3.3V, VIN = 5.0V
16
0.04 0.02 7 6
AAT1155
Loop Crossover Gain and Phase
L = 1.5Hy 180 135 90 Phase 4 0 -4 -8 -12 300F gain 100F 6.3 Ceramic TDK P/N C3225X5R0J107M Vishay GRM43SR60J107ME20L 200F gain 45 0 -45 -90 -135 -180 100000
12 8
Phase (Degrees)
Inductor Current (bottom) (A)
Output Ripple (top) (mV)
0.00 -0.02 -0.04 -0.06 -0.08 -0.10 -0.12 0 1 2 3 4 5
5 4 3 2 1
120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T
0 -1
Gain (dB)
-16 10000
time (sec)
Frequency (Hz)
Output Ripple IOUT = 3.0A, VOUT = 3.3V, VIN = 5.0V
4 2 7 6
Loop Crossover Gain and Phase
16 12 8 180 135 90
AC output ripple top (mV)
Inductor Current bottom (A)
Phase (Degrees)
0 -2 -4 -6 200F 6.3V Ceramic -10 TDK P/N C3325X5R0J107M Vishay GRM43SR60J107ME20L -12 0 1 2 3 -8
5 4 3 2 1 0 -1 4 5
Gain (dB)
4 0 -4 -8 -12
Gain
45 0 -45 -90
120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T 100000
-135 -180 1000000
Time (sec)
-16 10000
Frequency (Hz)
Output Ripple IOUT = 3.0A, VOUT = 3.3V, VIN = 5.0V
4 2 7 6 5 4 3 2 300F 6.3VCeramic TDK P/N C3325X5R0J107M Vishay GRM43SR60J107ME20L 0 1 2 3 4 5 1 0 -1
Tantalum Transient Response IOUT = 0 to 3.0A, VOUT = 3.3V, VIN = 5.0V
3.40 3.30 7 6 5 4 3 2 1 120F 6.3V Tantalum Vishay P/N 594D127X96R3C2T 0 100 200 300 400 500 0 -1
Inductor Current (bottom) (A)
AC output ripple top (mV)
0 -2 -4 -6 -8 -10 -12
Output Voltage (top) (mV)
Inductor Current bottom (A)
3.20 3.10 3.00 2.90 2.80 2.70 2.60
Time (sec)
Time (sec)
1155.2004.08.1.2
7
1MHz 2.5A Buck DC/DC Converter Typical Characteristics
Transient Response IOUT = 0 to 3.0A, VOUT = 3.3V, VIN = 5.0V
3.40 3.30 7 6
2x 100F 6.3V Ceramic TDK P/N C3325X5R0J107M Vishay GRM43SR60J107ME20L
AAT1155
Transient Response IOUT = 0 to 3.0A, VOUT = 3.3V, VIN = 5.0V
3.40 3.30 7 6
3x 100F 6.3V Ceramic TDK P/N C3325X5R0J107M Vishay GRM43SR60J107ME20L
Inductor Current (bottom) (A)
Inductor Current (bottom) (A)
Output Voltage (top) (mV)
3.20 3.10 3.00 2.90 2.80 2.70 2.60 0 100 200
Output Voltage (top) (mV)
5 4 3 2 1 0 -1
3.20 3.10 3.00 2.90 2.80 2.70 2.60 0 100 200
5 4 3 2 1 0 -1
300
400
500
300
400
500
Time (sec)
Time (sec)
8
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter Functional Block Diagram
VCC VP= 2.5V- 5.5V
AAT1155
REF
FB
OP. AMP
CMP
DH
LOGIC
LX
OSC
Temp. Sensing
EN
Applications Information
Main Control Loop
The AAT1155 is a peak current mode buck converter. The inner wide bandwidth loop controls the inductor peak current. The inductor current is sensed as it flows through the internal P-Channel MOSFET. A fixed slope compensation signal is then added to the sensed current to maintain stability for duty cycles greater than 50%. The inner loop appears as a voltage programmed current source in parallel with the output capacitor. The voltage error amplifier output programs the current loop for the necessary inductor current to force a constant output voltage for all load and line conditions. The feedback resistive divider is internal, dividing the output voltage to the error amplifier reference voltage of 1.0V. The error amplifier has a limited DC gain. This eliminates the need for external compensation components while still providing sufficient DC loop gain for good load regulation.
The crossover frequency and phase margin are set by the output capacitor value. Duty cycle extends to 100% as the input voltage approaches the output voltage. Thermal shutdown protection disables the device in the event of a short circuit or overload condition.
Soft Start/Enable
Soft-start controls the current limit when the input voltage or enable is applied. It limits the current surge seen at the input and eliminates output voltage overshoot. The enable input, when pulled low, forces the device into a low power non-switching state. The total input current during shutdown is less than 1A.
Power and Signal Source
Separate small signal ground and power supply pins isolate the internal control circuitry from switching noise. In addition, the low pass filter R1 and C3 in figure 3 filters noise associated with the power switching. 9
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter
Current Limit and Over Temp Protection
The AAT1155 over temp and current limit circuitry protects the AAT1155 as well as the external Schottky diode during overload, short circuit and excessive ambient temperature conditions. The junction over temp threshold is 140C nominal and has 15C of hysteresis. Typical graphs of the over temp load current vs. input voltage and ambient temperature are shown in the Typical Characteristics section.
AAT1155
The factor "k" is the fraction of the full load (40%) selected for the ripple current at the maximum input voltage. The corresponding inductor RMS current is:
IRMS = 2 I 2 I+ I O = 2.5A O 12
Inductor
The output inductor is selected to limit the ripple current to 20-40% of the full load current at the maximum input voltage. Manufacturer's specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the inductor saturation characteristics. The inductor should not show any appreciable saturation under all normal load conditions. During overload and short circuit conditions the inductor can exceed its peak current rating without affecting the converter performance. Some inductors may have sufficient peak and average current ratings yet result in excessive losses due to a high DCR. The losses associated with the DCR and its affect on the total converter efficiency must be considered. For a 2.5 Amp load and the ripple current set to 40% at the maximum input voltage, the maximum peak to peak ripple current is 1 Amp. Assuming a 5V 5% input voltage and 40% ripple the output inductance required is
L =I VOUT VOUT * k * FSW * 1 - VIN(MAX)
I is the peak to peak ripple current which is fixed by the inductor selection above. For a peak to peak current of 40% of the full load current the peak current at full load will be 120% of the full load. The 1.5H inductor selected from the Sumida CDRH6D38 series has a 11m DCR and a 4.0 Amp DC current rating with a height of 4 mm. At full load the inductor DC loss is 70 mW for a 0.84% loss in efficiency.
Schottky Freewheeling Diode
The Schottky average current is the load current times one minus the duty cycle.
VO 1 VIN
For VIN at 5 Volts and Vout at 3.3 Volts the average diode current is
V 3.3V = 0.85A I AVG = IO * 1 - O = 2.5A * 1 VIN 5.0V
With a 125C maximum junction temperature and a 120C/W thermal resistance the maximum average current is
IAVG = T J(MAX)- T AMB = 125C - 70C = 1.14A 120 C/ W * 0.4V
OUT
3.3V = * 1 - 3.3V 2.5A * 0.4 * 1MHz 5.25V
J-A * VFWD
= 1.23H
For overload, short circuit, and excessive ambient conditions the AAT1155 enters the over-temperature shutdown mode protecting the AAT1155 as well as the output Schottky. In this mode the output current is limited internally until the junction temperature reaches the temperature limit (see over temp characteristics graphs). The diode reverse voltage must be rated to withstand the input voltage.
10
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter
Diodes Inc. ROHM Micro Semi B340LA RB050L-40 5820SM 0.45V@3A 0.45@3A 0.46V@3A
AAT1155
IRMS =
1 2* 3
*
( VOUT+ VFWD) * (VIN - VOUT) L * F * VIN
3 Amp Surface Mount Schottky Diodes
Input Capacitor Selection
The primary function of the input capacitor is to provide a low impedance loop for the edges of pulsed current drawn by the AAT1155. A low ESR/ESL ceramic capacitor is ideal for this function. To minimize the stray inductance the capacitor should be placed as close as possible to the IC. This also keeps the high frequency content of the input current localized, minimizing the radiated and conducted EMI while facilitating optimum performance of the AAT1155. The proper placement of the input capacitor C1 is shown in the layout in figure 1. Ceramic X5R or X7R capacitors are ideal. The size required will vary depending on the load, output voltage, and input voltage source impedance characteristics. Typical values range from 1F to 10 F. The input capacitor RMS current varies with the input voltage and the output voltage. It is highest when the input voltage is double the output voltage where it is one half of the load current.
VO V * 1- O VIN VIN
For a ceramic output capacitor the dissipation due to the RMS current and output ripple associated with are negligible. Tantalum capacitors, with sufficiently low ESR to meet output ripple requirements, generally have an RMS current rating much greater than that actually seen in this application. The maximum tantalum output capacitor ESR is
ESR
VRIPPLE I
Where I is the peak to peak inductor ripple current. Due to the ESR zero associated with the tantalum capacitor, smaller values than those required with ceramic capacitors provide more phase margin a with greater loop crossover frequency.
Layout
Figures 6 and 7 display the suggested PCB layout for the AAT1155. The following guidelines should be used to help insure a proper layout. 1. The connection from the input capacitor to the Schottky anode should be as short as possible. 2. The input capacitor should connect as closely as possible to VPOWER (pins 5 and 8) and GND (pin 2). 3. C1, L1, and CR1 should be connected as closely as possible. The connection from the cathode of the Schottky to the LX node should be as short as possible. 4. The feedback trace (pin 1) should be separate from any power trace and connect as closely as possible to the load point. Sensing along a high current load trace can degrade DC load regulation. 5. The resistance of the trace from the load return to the gnd (pin 2) should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal reference ground and the load rtn. 6. R1 and C3 are required in order to provide a cleaner power source for the AAT1155 control circuitry.
IRMS = IO *
A high ESR tantalum with a value about 10 times the input ceramic capacitor may also be required when using a 10F or smaller ceramic input bypass capacitor. This dampens out any input oscillations that may occur due to the source inductance resonating with the converter input impedance
Output Capacitor
With no external compensation components, the output capacitor has a strong effect on the loop stability. Larger output capacitance will reduce the crossover frequency with greater phase margin. A 200F ceramic capacitor provides sufficient bulk capacitance to stabilize the output during large load transitions and has ESR and ESL characteristics necessary for very low output ripple. The RMS ripple current is given by
1155.2004.08.1.2
11
1MHz 2.5A Buck DC/DC Converter
Thermal
The losses associated with the AAT1155 output switching MOSFET are due to switching losses and conduction losses. The conduction losses are associated with the RDS(ON) characteristics of the output switching device. At the full load condition, assuming continuous conduction mode (CCM), an accurate calculation of the RDS(ON) losses can be derived from the following equations.
P = I RMS2 * RDS(ON) ON
AAT1155
Design Example
IOUT 2.5A IRIPPLE 40% of full load at max Vin VOUT 2.5V VIN 5V 5% FS 1MHz TMAX = 70C Inductor Selection
RDS(ON) losses
L=
IRMS =
2 2 I *D IO + 12
VOUT VOUT * 1IO * k * F VIN
=
Internal switch RMS current D is the duty cycle and VF is the forward drop of the Schottky diode.
3.3V 3.3V * 1= 1.23H 5.25V 2.5A * 0.4 * 1MHz
Use standard value of 1.5 H Sumida inductor Series CDRH6D38.
D=
VO + VF VIN + VF
I =
VO V 1- O = L * F VIN
IQ is the peak to peak inductor ripple current. A simplified form of calculating the RDS(ON) and switching losses is given by
3.3V 3.3V = 0.82A 11.5H * 1MHz 5.25V
I PK = IOUT + I = 2
P=
I O 2 * R DS(ON) Vo + tSW *F * I O + I Q * VIN VIN
2.5A + 0.41 = 2.91A
where IQ is the AAT1155 quiescent current. Once the total losses have been determined the junction temperature can be derived. The thermal resistance (JA) for the MSOP-8 package mounted on an FR4 printed circuit board in still air is 150C/W. TJ = P QJA + TAMB TAMB is the maximum ambient temperature and TJ is the resultant maximum junction temperature.
AAT1155 Junction Temperature
P= ON IO2 * RDS(ON) * VO tSW * F * IO + IQ * VIN = + VIN 2
2.52 * 70m * 3.3V 20ns * 1MHz * 2.5A + + 690A 5V 2 0.42 Watts
TJ(MAX)= TAMB + JA * P = 70C + 150C/W * 0.42W = 133C
12
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter
Diode
V IDIODE= IO * 1 - O = VIN 3.3V = 0.93A 2.5A * 1 5.25V
VFW = 0.35V P DIODE = VFW * IDIODE =
0.35V * 0.93A = 0.33A
Given a case to ambient thermal resistance of 120C/W from the manufacturer's data sheet, TJ(MAX) of the diode is
AAT1155
The ESR requirement for a tantalum capacitor can be estimated by
ESR
VRIPPLE 100 mV = = 111m I 0.9A
1 *
IRMS = 1
(VOUT+ VFWD) * (VIN - VOUT)
L * F * VIN
2* 3 *
=
T J(MAX) = T AMB + JA * P = 70C + 120C / W * 0.33W = 109C
3.65V *1.7 V = 240mArms 1.5H * 1MHz * 5V 2* 3 Two or three 1812 X5R 100uF 6.3V ceramic capacitors in parallel also provide sufficient phase margin. The low ESR and ESL associated with ceramic capacitors also reduces output ripple significantly over that seen with tantalum capacitors. Temperature rise due to ESR ripple current dissipation is also reduced.
Input Capacitor
The input capacitor ripple is:
Output Capacitor
The output capacitor value required for sufficient loop phase margin depends on the type of capacitor selected. For a low ESR ceramic capacitor a minimum value of 200F is required. For a low ESR tantalum capacitor lower values are acceptable. While the relatively higher ESR associated with the tantalum capacitor will give more phase margin and a more damped transient response, the output voltage ripple will be higher. The 120F Vishay 594D tantalum capacitor has an ESR of 85 m and a ripple current rating of 1.48 Arms in a C case size. Although smaller case sizes are sufficiently rated for this ripple current, their ESR level would result in excessive output ripple.
IRMS = I O *
V V O * 1 - O = 1.82Arms VIN VIN
In the examples shown C1 is a ceramic capacitor located as close to the IC as possible. C1 provides the low impedance path for the sharp edges associated with the input current. C4 may or may not be required depending upon the impedance characteristics looking back into the source. It serves to dampen out any input oscillations that may arise from a source that is highly inductive. For most applications where the source has sufficient bulk capacitance and is fed directly to the AA1155 through large PCB traces or planes it is not required. When operating the AAT1155 evaluation board on the bench C4 is required due to the inductance of the wires running from the laboratory power supply to the evaluation board.
1155.2004.08.1.2
13
1MHz 2.5A Buck DC/DC Converter
Vin 3.5V-5.5V Vout 3. V @ 2.5A 3
AAT1155
Efficiency vs. Load Current VIN = 5.0V, VOUT = 3.3V
100 95
R1 100 C4 100F
R2 100k
U1 AAT1155-3. 3 FB VP
GND LX EN C1 10F C3 0.1F LX
Efficiency (%)
L1 1.5H
90 85 80 75 70 65 60 0.01 0.1 1 10
VCC VP
D1 B340LA
C2 120F
+ -
rtn
C1 Murata 10F 6.3V X5R GRM42-6X5R106K6.3 C2 Vishay120F 6.3V 594D127X96R6R3C2T C3 0. F 0603ZD104M AVX 1 C4 Vishay Sprague 100F 16V 595D107X0016C 100F 16V D1 B340LA Diodes Inc. L1 CDRH6D28-1.5H Sumida Options C2 MuRata 100F 6.3V GRM43-2 X5R 107M 100F 6.3V (two or three in parallel) C2 TDK 100F 6.3V C3325X5R0J107M 100F 6.3V (two or three in parallel)
Output Current (A)
Figure 1. 3.3 Volt 3 Amp output Efficiency
Figure 2. 5 Volt Input 3.3 Volt Output
Adjustable Output
For applications requiring an output other than the fixed outputs available, the 1V version can be programmed externally. Resistors R3 and R4 of figure 5 force the output to regulate higher than 1 Volt. For
accurate results (less than 1% error for all outputs) select R4 to be 10k. Once R4 has been selected R3 can be calculated. For a 1.25 Volt output with R4 set to 10k R3 is 2.5k. R3 = (VO - 1) * R4 = 0.25 * 10k = 2.5k
Vin 2.7V-5.5V VOUT 1.25V @ 2.5A R3 2.55k
R1 100 C4 100F
R2 100k
U1 AAT1155-1.0 FB VP L1 1.5H
GND LX EN C1 10F C3 0.1F R4 10.0k LX
VCC VP
D1 B340LA
C2 120F
rtn
C1 Murata 10F 6.3V X5R GRM42-6X5R106K6.3 C2 Vishay 120F 6.3V 594D127X96R6R3C2T C3 0. F 0603ZD104M AVX 1 C4 Vishay Sprague 100F 16V 595D107X0016C 100F 16V D1 B340LA Diodes Inc. L1 CDRH6D28-1.5H Sumida Options C2 MuRata 100uF 6.3V GRM43-2 X5R 107M 100F 6.3V (two or three in parallel) C2 TDK 100F 6.3V C3325X5R0J107M 100F 6.3V (two or three in parallel)
Figure 3. AAT1155 Evaluation Board with adjustable output
14
1155.2004.08.1.2
1MHz 2.5A Buck DC/DC Converter
AAT1155
Figure 6. Evaluation Board Top Side
Figure 7. Evaluation Board Bottom Side
Capacitors Part Number
C4532X5ROJ107M GRM43-2 X5R 107M 6.3 GRM43-2 X5R 476K 6.3 GRM42-6 X5R 106K 6.3 594D127X_6R3C2T 595D107X0016C
Manufacturer
TDK MuRata MuRata MuRata Vishay Vishay
Capacitance (F)
100 100 47 10 120 100
Voltage (V)
6.3 6.3 6.3 6.3 6.3 16
Temp Co.
X5R X5R X5R X5R
Case
1812 1812 1812 1206 C case C case
Inductors Part Number
CDRH6D38-4763-T055 N05D B1R5M NP06DB B1R5M LQH55DN1R5M03 LQH66SN1R5M03
Manufacturer
Sumida Taiyo Yuden Taiyo Yuden MuRata MuRata
Inductance (H)
1.5 1.5 1.5 1.5 1.5
I (Amps)
4.0 3.2 3.0 3.7 3.8
DCR ()
.014 .025 .022 .022 .016
Height (mm)
4.0 2.8 3.2 4.7 4.7 shielded Non shielded shielded Non shielded shielded
Diodes Manufacturer
Diodes Inc. ROHM Micro Semi
Part Number
B340LA RB050L-40 5820SM
Vfwd
0.45V @ 3A 0.45 @ 3A 0.46V @ 3A
1155.2004.08.1.2
15
1MHz 2.5A Buck DC/DC Converter Ordering Information
Output Voltage 1.0V (Adj. VOUT 1.0V) 1.8V 2.5V 3.3V Package MSOP-8 MSOP-8 MSOP-8 MSOP-8 Marking KXXYY KYXYY ILXYY IKXYY Part Number (Tape and Reel) AAT1155IKS-1.0-T1 AAT1155IKS-1.8-T1 AAT1155IKS-2.5-T1 AAT1155IKS-3.3-T1
AAT1155
Note: Sample stock is held on part numbers listed in bold. Note 1: XYY = assembly and date code.
Package Information
MSOP-8
4 4 1.95 BSC
3.00 0.10
4.90 0.10
0.60 0.20 PIN 1 0.254 BSC 0.95 REF
3.00 0.10 10 5 0.95 0.15 0.85 0.10
0.075 0.075 0.65 BSC 0.30 0.08
All dimensions in millimeters.
AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed.
Advanced Analogic Technologies, Inc.
830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 16
1155.2004.08.1.2
GAUGE PLANE
0.155 0.075

▲Up To Search▲

Price & Availability of AAT1155

	To Download AAT1155 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .